[Download] Hitachi AC Drive Manual SJ700-2 VFD & All VFD

[Download] Hitachi AC Drive Manual SJ700, WL200, L200, WJ200, J100E5, L300P, J300, SJ100, SJ200, X200, L700, SJ-P1, NE-S1 Series VFD Manual Free Download 100% Real

Hitachi is a Multinational Manufacturer Company in the World. Hitachi Ltd was founded in Japan in 1910. The Hitachi Company Manufacture Variety of types of Power, Industrial, and Home Appliance Products such as Programmable Logic Controller (PLC), Inverters, Ac Servo Drive, Human Machine Interface (HMI), Transformer, Motor, Switches and Breakers, Rope Hoist & Chain Hoist, Air Compressor, Nitrogen Gas Generator, Pumps, Blower, Marking System, and General Products, etc. So Today plchmiservo.com would like to share the [Download] Hitachi AC Drive Manual SJ700-2 VFD & All VFD User manual PDF, Also how to download the SJ-700-2 series Hitachi AC Drive Manual, WL200 Series, L200 Series, WJ200 Series, J100E5 Series, L300P Series, J300 Series, SJ100 Series, SJ200 Series, X200 Series, L700 series, SJ-P1 Series, NE-S1 VFD User manual, and How to setup the Hitachi SJ700 Series inverter and How to Program by using it manually

Programming Parameter Description of Hitachi VFD SJ700 Series VFD:

At first, see these parameters Code Functions carefully then program the Hitachi VFD SJ700 Series VFD step by step

D Codes-Monitoring Functions-For Monitor

F Codes-Main Profile Parameters- For Program

A Codes-Standard Functions- For Program

B Codes-Fine Tuning Functions- For Program

C Codes-Intelligent Terminal Functions- For Program

H Codes-Motor Constant Related Functions- For Program

P Codes-Pulse Train input Torque & Communication Functions- for Program

U Codes-User Selected parameters Functions- for Program

E Codes-Error Codes

How to set the Hitachi SJ700 Series VFD Parameter

For Example, We have set the parameter for only one motor but we could Connect another 2 motors.

A001: Frequency Source Setting

VR: 00: Keypad Potentiometer

TRM: 01: Control Terminal

A001: Run Source Setting Commend

TRM: 01: Input Terminal Mode FWD/REV

REM: 02: Run Key on Keypad

RS485: 03: For the RS485 command

A003: Base Frequency Setting (30 to Maximum Frequency)-50HZ & 60HZ

A004: Maximum Frequency Setting (30-400HZ) for Example 50HZ & 60HZ

F001: Output Frequency setting (0 to 400HZ)-For Example 50HZ/ 60HZ

F002: Acceleration 1 Time Setting (0-3600 Second)-(10Second, 20 Second, 30 etc)

F003: Deceleration 1 Time Setting (0-3600 Second)-(15Second/ 25 second/30S etc)

F004: Keypad Run Key Routing

FW: 00- Forward

RV: 01- Reverse

F06: Maximum output Voltage-Example 440V

F11: Rated Current-Depend on Motor

F15: Frequency Upper Limit Setting: 50 HZ, 60 HZ, etc

F16: Frequency Lower Limit Setting -0HZ

A071: PID Enable

How to lock the parameter

Note That: If you could not set the parameter then you will check all Lock Parameters

B031: Software Lock Mode Selection

MD0-00-Low Level Access (SFT) Input All Block

MD2-02-No Access to Edit

B035-Rotational Direction Lock

Free: 00-Enable for both direction

FW: 01-Enable Only Forward

RV: 02- Enable Only Reverse

For JOG Frequency

A038– Jog Frequency Setting (0.5 to 9.9 HZ)- 5HZ/10HZ etc

A039– Jog Stop Mode

FRS: 00- Free Run Stop Jogging Disable during Motor Run

DEC: 01- Control Deceleration

For Terminal Setting

C001: Terminal 1 Function

C002: Terminal 2 Function

……………………………….

C008: Terminal 8 Function

Output Terminal Configuration

C021: Terminal 11 Function

C022: Terminal 12 Function

C023: Terminal 13 Function

C024: Terminal 14 Function

C025: Terminal 15 Function

For Multi-Function

A019: Multi-Speed Operation Selection

Binary: 00- 16 Stages

Bit: 01- 8 Stages

A019: Multi-Stage Frequency Setting (0-360HZ) 1St Motor

Multistage “Frequency” Setting

A021: -Multistep Frequency Setting-Speed 1 for Multiple motors

A022: -Multistep Frequency Setting-Speed 2

A023: -Multistep Frequency Setting-Speed 3

A024: -Multistep Frequency Setting-Speed 4

…………………………………………..

A035: -Multistep Frequency Setting-Speed 15 for Multiple motors